Which lathe models that have D1-3 camlock spindles?

[TorontoBuilder]

I can only think of four sources for D1-3 spindle cams available to those people in Canada.

MSC, and Penn Tools sell new replacements, for $58 and $90.80 USD each respectively. x3 Ouch.

I perhaps could find Taiwanese lathe manufacturer that manufactures a lathe that still uses a D1-3 spindle and try to buy directly from them. Lots of work involved in this.

I could potentially make one of acceptable quality to work in my lathe.

Or I can find someone parting out a lathe with a d1-3 camlock spindle and buy that to use the parts from it

So what lathes came with a d1-3 spindle?

 

[DavidR8]

I thought the CX707 was D1-3 but turns out it's D1-4

 

[TorontoBuilder]

I thought the CX707 was D1-3 but turns out it's D1-4

yeah, almost all grizzly and precision matthews lathes use d1-4 as well. At one time I thought there were some older grizzlies that had d1-3 mounts but no longer the case.

 

[DavidR8]

Found these:

Camlock Studs D1-3 9/16 Diameter Metric Thread - ID: 1063-7-899-103

 

[Brent H]

@TorontoBuilder : the 10/12 “ Utilathes have a D1-3 spindle. I purchased my adapter plates on Amazon:

It was not that expensive in 2019

 

[TorontoBuilder]

To clarify, I'm in need of spindle CAMS like this

To replace the ones the previous owner of my lathe bashed in.... so I had to weld a bolt into the cam to get it out. you can see they're all fractured and worn beyond use

 

[TorontoBuilder]

@TorontoBuilder : the 10/12 “ Utilathes have a D1-3 spindle. I purchased my adapter plates on Amazon:

Thanks Brent. I had thought some standard modern lathes used d1-3. But I only knew the 2000 series took d1-4 for sure.

At least I know what it most likely model to look for being parted out now. These would be cheaper than a monarch 10EE spindle

 

[DavidR8]

Whoops I should have read more slowly.

 

[Mcgyver]

you guys are talking pins...but I think he needs the cams

Some SM's and the 10ee are D1-3. Getting a lathe for less 58US x3 and the trouble/cost of moving it seems doubtful though. I'd be a toss up between make or buy. You'll be the better 300 after exchange, hst, shipping and carrier door step extortion fee. They aren't complicated but its a few operations and I aleady have 800 years of work...so a toss up.

 

[TorontoBuilder]

you guys are talking pins...but I think he needs the cams

Some SM's and the 10ee are D1-3. Getting a lathe for less 58US x3 and the trouble/cost of moving it seems doubtful though. I'd be a toss up between make or buy. You'll be the better 300 after exchange, hst, shipping and carrier door step extortion fee. They aren't complicated but its a few operations and I aleady have 800 years of work...so a toss up.

I just want to get the parts asap... I figured the off chance one of the dudes south of the tri-cities has a lathe getting parted out I could just get a spindle out of.. I dont just need the cams, I need the can retention screw assemblies as well...

I sent a missive to colchester parts and another UK outfit and am awaiting their replies. I am happy I was able to knock out a few tasks on my long list bringing me closer to getting the chipmaster restored,

 

[Former Member]

Here is a source:

https://www.mscdirect.com/product/details/56451370

Not cheap but new and available.

 

[Tom Kitta]

Here is a source:

https://www.mscdirect.com/product/details/56451370

Not cheap but new and available.

Yeah 60 USD each....

I have D1-3 lathe. The D1-3 is popular for older precision lathes. D1-3 seems to be the ticket for lathes with swing of between 10 and 12. Reason D1-4 is so popular is b/c it gives bigger through bore hole.

 

[darrin1200]

I got parts for my 10” Utilathe, which uses D1-3, from Racer Machinery in Cambridge. They own Standard Modern as far as I know, and still supply parts for older machines.
+1.519.623.6223

Standard Modern Lathes | CNC & Manual Lathe Manufacturer

Racer Machinery International Inc. is a proud machine tool manufacturer of renowned Standard Modern lathes brand including the well known 1340 Engine Lathe. With over 80 years of history, pride and experience behind every machine.

standardmodernlathes.com

 

[TorontoBuilder]

I got parts for my 10” Utilathe, which uses D1-3, from Racer Machinery in Cambridge. They own Standard Modern as far as I know, and still supply parts for older machines.
+1.519.623.6223

Standard Modern Lathes | CNC & Manual Lathe Manufacturer

Racer Machinery International Inc. is a proud machine tool manufacturer of renowned Standard Modern lathes brand including the well known 1340 Engine Lathe. With over 80 years of history, pride and experience behind every machine.

standardmodernlathes.com

Thank you so much for this info!

 

[buckbrush]

D1-3, Monarch 10ee, Boxford Industrial 10x30 geared head

 

[TorontoBuilder]

Update, racer machinery does not have many parts for older standard modern lathes equipped with D1-3 spindles, and they specifically don't have cams, detent plungers, compression springs and screws.

They referred me to LeBlonde USA. I waiting to hear back from them

Colchester Parts failed to respond to my enquiry about these parts. Previously they did respond to my other parts enquiries.

Not a peep from Myford...

 

[Susquatch]

They referred me to LeBlonde USA. I waiting to hear back from them

Leblonde is pretty good. They sent me new way oil rollers and springs for my surface grinder. Shoot me a PM if you want a name and phone number. They were pretty good by email too - responded within a day.

 

[Johnwa]

A bit OT, I didn’t get this because they were out of stock. I did get 1.5x8 screw on one though. They are pretty reasonably if you’re south of the border.

All Industrial 47912 | Threaded Back Plate Adapter 5" 3-Hole D1-4 for Lathe Chucks

We distribute top-quality industrial tools and machine shop supplies at the best prices. View our collection of CNC machinist supplies and tooling packages.

allindustrial.com

 

[TorontoBuilder]

Update 2

Colchester spares got back to me... they have all the original parts available. But the price, sweet baby jesus, I wont be able to eat for a year

1029 - Spindle Cam x 3, use D902H044.1, £41.00 each, ex stock

1161 - Plunger x 3, £22.40 each, ex stock

1225 - Spring x 3, £5.40 each, ex stock

1200 - Plunger screw x 3, £6.24 each, ex stock

£15.00 Carriage.

Convert that to CAD and the cost is over $405.00 plus HST upon arrival

 

[DavidR8]

But no VAT