• Scam Alert. Members are reminded to NOT send money to buy anything. Don't buy things remote and have it shipped - go get it yourself, pay in person, and take your equipment with you. Scammers have burned people on this forum. Urgency, secrecy, excuses, selling for friend, newish members, FUD, are RED FLAGS. A video conference call is not adequate assurance. Face to face interactions are required. Please report suspicions to the forum admins. Stay Safe - anyone can get scammed.

METAL BANDSAW, $350, Taber, AB

jcdammeyer said:
Mine has one two that screws in place of the small guide. Also thick sheet metal but certainly no T slot.
Neither PA nor KMS show the auxiliary table for vertical use.
Click to expand...

That is wrong band saw - its 7 x 10 in your link, the correct one is -

"Vertical and horizontal cutting capabilities. "

KMS one is
www.kmstools.com

King Industrial Metal Cutting Band Saw

This is a very popular tool, ideal for anyone who needs a compact, convenient and durable metal-cutting band saw. The KC-129C cuts round material up to 5" in diameter and rectangular material up to 4-1/2" x 6". It also offers three cutting speeds and the
www.kmstools.com www.kmstools.com
"Includes table for vertical cutting"

As many others have mentioned, included table is junk. When I sold my BS I actually forgot to give it to the new owner - but no loss, it was just flimsy sheet metal.
 
Tom Kitta said:
As many others have mentioned, included table is junk. When I sold my BS I actually forgot to give it to the new owner - but no loss, it was just flimsy sheet metal.
Click to expand...

Sadly, I have one of those with the flimsy sheet metal table. I'd like to make a new table out of 3/8 or even 1/2 plate aluminium.

But I don't like the tiny screw's that hold it in place.

Did you make a better support system too?
 
Susquatch said:
Sadly, I have one of those with the flimsy sheet metal table. I'd like to make a new table out of 3/8 or even 1/2 plate aluminum.

But I don't like the tiny screw's that hold it in place.

Did you make a better support system too?
Click to expand...
One setup I saw, I think from Mark Winquist of Winky's Workshop had a base that clamped into the saw vise with an attached table.
 
David_R8 said:
One setup I saw, I think from Mark Winquist of Winky's Workshop had a base that clamped into the saw vise with an attached table.
Click to expand...

I'll look for it. But my instincts are not happy. The vise on mine is miles from where a table would go. Vise is used in horizontal mode - table is vertical mode.
 
Susquatch said:
Sadly, I have one of those with the flimsy sheet metal table. I'd like to make a new table out of 3/8 or even 1/2 plate aluminium.

But I don't like the tiny screw's that hold it in place.

Did you make a better support system too?
Click to expand...

No managed to sell it before I did any changes.

I actually just picked up a small portable bandsaw for cutting small stuff - and it feels like it can do almost anything this machine can do. It has a bit smaller cut range at around 3.5 -- 4". Strange BS length of 52.5 in.
 
@Susquatch pics from a YT vid.

Screenshot 2023-06-06 at 2.27.03 PM.webp
Screenshot 2023-06-06 at 2.27.34 PM.webp
 
My table is a 3”x3” piece of ⅛” aluminum. It’s small enough that I can leave it in place. It is moderately useful.
 
I used 3/16 or 1/4 steel plate and made it as big as possible that it can stay on when using it normally. The two screws hold it in place fine.

I like his cooling setup
 
You must log in or register to reply here.
Back
Top